Digital Identification Solutions XID 8300 Manual de instrucciones descargar pdf (Pagina 29)

Instruction Manual Page 29

EDIsecure

XID 8300 Ethernet Status Monitor

Error Code

Displayed Message

Actions

restore the retransfer film.

0103A100

Mark on Retransfer Film could not be

detected. Please set Retransfer Film

correctly.

Install the retransfer film correctly. After

installing, close the printer door, followed by

pressing the RESET and ENTER buttons in

sequence to initialize the printer.

0103B000

Ink Ribbon is broken.

Refer to “Mending broken ink ribbon and

retransfer film” in the “XID 8300 Instruction

Manual” (separate booklet) on procedures to

restore the ink ribbon.

0103B100

Ink Ribbon cannot be controlled.

Please set Ink Ribbon correctly.

Install the ink ribbon correctly. After

installing, close the printer door, followed by

pressing the RESET and ENTER buttons in

sequence to initialize the printer.

0103BB00

Card Jam happens in External IC unit.

Please remove the card in External IC

unit.

Press the RESET and ENTER buttons in

sequence to initialize the printer. If the card

is not ejected, turn off the power and remove

the card.

01044400

0104D800

0104FA00

Hardware failure happens in the

printer unit. Please turn off and on the

printer power to initialize the printer.

Turn off the power of the printer and turn on

again. Call for servicing if this problem

recurs.

0104A900

MG encoder is not set correctly.

Please turn off the printer power and

set MG unit correctly.

Turn off the power of the printer and turn on

again. Call for servicing if this problem

recurs.

0104AB00

Mechanical failure happens in the MG

encoder. Please turn off and on the

printer power to initialize the printer.

Turn off the power of the printer and turn on

again. Call for servicing if this problem

recurs.

0104AC00

Hardware failure happens in the MG

encoder. Please turn off and on the

printer power to initialize the printer.

Turn off the power of the printer and turn on

again. Call for servicing if this problem

recurs.

0104AF00

Communication error happens

between printer and MG encoder.

Please turn off and on the printer

power to initialize the printer.

Turn off the power of the printer and turn on

again. Call for servicing if this problem

recurs.

0104B900

External IC unit is not set correctly.

Please turn off the printer power and

set External IC unit correctly.

Turn off the power of the printer and turn on

again. Call for servicing if this problem

recurs.

0104BA00

Dip switch setting in the external IC

unit is not correct. Please turn off the

printer power and correct Dip switch

setting in External IC unit.

Turn off the power of the printer and turn on

again. Call for servicing if this problem

recurs.

0104BE00

Communication error happens

between printer and External IC unit.

Please turn off the printer power and

connect communication cable

correctly.

Turn off the power of the printer. Unplug

the cable connecting the external IC unit to

the printer, and plug in again.

0104BF00

Communication error happens

between printer and laminator. Please

turn off the printer power and connect

communication cable correctly.

Turn off the power of the printer. Unplug the

cable connecting the laminator to the printer,

and plug in again.

Call for servicing if this problem recurs.

0104C000

Hardware failure happens in the

turnover unit. Please turn off and on

the printer power to initialize the

printer.

Turn off the power of the printer and turn on

again. Call for servicing if this problem

recurs.

0104C100

Hardware failure of Heater Cam

happens. Please turn off and on the

printer power to initialize the printer.

Turn off the power of the printer and turn on

again. Call for servicing if this problem

recurs.

0104F000

The temperature of Retransfer

Roller is too hot. Please turn off the

Turn off the power of the printer. Turn on

again after the temperature of the retransfer

1 2 ... 24 25 26 27 28 29 30 31 32

Comentarios a estos manuales

Sin comentarios

Digital Identification Solutions XID 8300 Manual de instrucciones Pagina 29

Comentarios a estos manuales

Relacionado con productos y manuales para Impresión y escaneo Digital Identification Solutions XID 8300